MATT GLAZING DECORATIONS:

CRAQUELÉ effect

Using a roller apply a coating of CeboFix R tinted into the desired colour that will determine the cracks colour. When CeboFix R is completely dry, apply a coating of CeboBreak working in criss cross strokes until the surface is completely saturated. When the surface is dry, it should be translucid. After minimum 4 hours and maximum 24 hours, using a steel trowel apply a coating of uniform thickness of white CeboArt Model, then create the required esthetic effect working the surface with the trowel, making criss cross irregular strokes. Wait for the cracks to form. Before the product gets completely dry, smooth it out, slightly flattening the salient patches.

Retrò DESIGN effect

Apply one coating of CeboArt Model white, levelling and smoothing the surface with a stainless steel trowel (A/39-A/40). When the surface is dry, attach the stencil to the wall with some masking tape and apply a second coating of CeboArt Model max 2 mm thick, making strokes evenly from the edges of the stencil to its centre. Proceed on all the surface, positioning one or more patterns randomly, but leave some patches empty – they will be coated with CeboArt Model later. Before the product gets completely dry, smooth it out with a trowel, flattening slightly the salient patches. If the product is too dry, you can wet it with sprayed water. When the surface is dry, proceed applying CeboWax or CeboStyle Antico.

Note: in case you wish to combine the desired effect with the CRAQUELE effect, see the previous paragraph.

Underwater DESIGN effect

Prepare the surface with CeboFix R. When it is ready, plumb the stencil and attach it to the wall with some masking tape: using a stainless steel trowel (A/39-A/40), apply a coating of CeboArt Model white, max 2 mm thick, coat evenly the stencil pattern. Be careful to apply little product in overlapping spots. Afterwards, move the stencil following the pattern, and continue as described before, repeating the operation as many times as necessary. Before the product gets completely dry, smooth it out with a clean trowel, and when the wall is dry, emery it to eliminate all the eventual imperfections and uneven spots. Apply the second coating of CeboArt Model with the help of a trowel, smoothing and tightening the product to regulate and highlight the pattern. If the product is too dry, you can wet it with sprayed water. When the product is completely dry, continue applying CeboWax.

TIVOLI effect

Using a steel trowel apply a coating of uniform 1-2 mm thickness of white CeboArt Model. While the product is still wet, work the surface with the special CeboSign tool (A/35) to create the veins typical for stone. In order to obtain a more natural effect proceed irregularly and avoid repeating the same pattern. Using a punch make incisions on the surface to create the effect of stone blocks. Before the product gets completely dry, smooth it out with a trowel, flattening slightly the salient patches. If the product is too dry, you can wet it with sprayed water.

CeboWax

A water-based transparent finish for indoor spaces, made of natural bee wax and carefully selected binding materials, which allows to protect and make the surface water-repellent, maintaining its air permeability. Colored CeboWax is only to 30% diluted with water. It is applied in two coatings onto completely dry CeboArt Model, from the bottom upwards and with the help of a synthetic sponge (A/4). For darker tints it is recommended to apply the first coating of non-colored CeboWax, diluted with water to 30-40%.

METALLIC EFFECTS:

CREATIVA effect

Using a steel trowel apply a thick coating of uniform thickness of white CeboArt Model. While the product is still wet, work the surface with the special Sahara tool (A/64) to create the chosen pattern. Before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

DRAFT effect

Using a stainless steel trowel apply a non-uniform coating of white CeboArt Model varying the application direction; while the product is still wet, make irregular incisions on the surface using the special CeboSign tool (A/35). Before the product gets completely dry, smooth the surface out with a trowel, flattening slightly the salient patches; if the product is too dry, you can wet it with sprayed water.

ONDA effect

Apply vertically or horizontally a coating of uniform thickness of white CeboArt Model using the toothed edge of the stainless steel Shark trowel (A/55); then smooth the product out using the smooth edges of the same trowel. While the product is still wet, work the surface with the PVC trowel “Onda 4” (A/56) following the chosen vertical or horizontal direction. Before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

ZEFFIRO effect

Apply a coating of uniform thickness of white CeboArt Model using the toothed edge of the Shark trowel (A/55) and making horizontal or vertical strokes: make sure to smooth it subsequently using the smooth edge of the Shark trowel. It is recommended to apply and then work the product in bands about 1 metre wide. Using the special CeboSign tool (A/35) scratch the surface in the chosen direction (horizontal or vertical); before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

SBRECCIATO effect

Apply diagonally a coating of uniform thickness of white CeboArt Model using the toothed edge of the stainless steel Shark trowel (A/55); then make a second passage using the smooth edges of the same trowel until you get an alternate sequence of smooth and diagonal bands of different dimensions. While the product is still wet, dab the surface or scratch it irregularly with the CeboSign tool (A/35) following the direction of the strokes. Before the product gets completely dry, smooth it out with a stainless steel trowel, flattening slightly the salient patches. If the product is too dry, you can wet it with sprayed water.

COCCODRILLO effect

Apply vertically or horizontally a coating of uniform thickness of white CeboArt Model, using the toothed edge of the stainless steel Shark trowel (A/55); then smooth the product out using the smooth edges of the same trowel. While the product is still wet, work the surface with the special roller “Coccodrillo” (A/61-A/62) following the chosen vertical or horizontal direction. As you can see in the pictures, to avoid the problem with joints, we recommend not to work on the whole walls at once. Firstly, coat their smaller parts, doors, niches, etc. Before the product gets completely dry, smooth it out, slightly flattening the salient patches. If the product is too dry, you can wet it with sprayed water.

Note: to avoid the problem with joints, we recommend not to work on the whole walls at once. Firstly, coat their smaller parts, doors, niches, etc.

Retrò DESIGN effect

see the description in the previous page.

Salient DESIGN effect

Apply the first coating of CeboArt Model white, levelling and smoothing the surface with a stainless steel trowel (A/39-A/40). When the surface is dry, plumb the stencil and attach it to the wall with some masking tape: and apply a second coating of CeboArt Model max 2 mm thick, making strokes evenly from the edges of the stencil to its centre, making sure the product doesn’t get to the back side. Afterwards, attach another stencil and continue as described before, repeating the operation as many times as necessary. It is recommended to remove the stencils while the product is still wet, in that way any eventual defect may be removed when the surface is dry. Proceed to applying CeboStyle Antico.

CeboStyle Antico -Acrylic metallic finish

When CeboArt Model is completely dry, apply two coatings of CeboStyle Antico using the CeboSi brush (A/26-27), following the pattern direction, then immediately shade the surface with a synthetic sponge (A/4); dilute the second coating with water up to 30-40%.

NEOCLASSICAL EFFECTS: